opc_loader

EGW S&W M&P Red Dot Mount Vortex Venom

EGW S&W M&P Red Dot Mount Vortex Venom
Vortex Viper / Venom S&W M&P Sight Mount (fits Burris FastFire and Docter)

70,25
x
Stock
Stock:
  5  In stock
Item No.: EGW49308

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot
Sightmark Core Shot

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

This mount will fit:
Smith & Wesson M&P Full Size
Smith & Wesson M&P 2.0 Full Size
Smith & Wesson M&P 22 Full Size
Smith & Wesson M&P Compact
Smith & Wesson M&P 2.0 Compact
Smith & Wesson SD9VE
Smith & Wesson SD40VE
Smith & Wesson M&P Shield

This mount does not fit:
Smith & Wesson M&P C.O.R.E Series (Already optics ready)
Smith & Wesson M&P Shield EZ .380
Smith & Wesson M&P Shield EZ 9mm
Smith & Wesson M&P .22 Compact
Smith & Wesson SW9VE
Smith & Wesson SW40VE

The hole for the set screw on this mount is drilled off-center intentionally. This is to allow the set screw to be tightened against the bottom of the dovetail cut in the slide. This creates an upward force on the dovetail of the mount. If the hole were cut in the center of the dovetail, the set screw would fall through the hole cut in the center of the slide which would render the set screw useless.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

EGW S&W M&P Red Dot Mount Vortex Venom does not have any reviews yet. Share your experiences and post a review.
EGW S&W M&P Red Dot Mount Vortex Venom


Article numbers
EAN:
841370113934
SKU:
49308